AN/ARC-5 RADIO SET - RECEIVER AND TRANSMITTERS
The AN/ARC-5 Command Radio Set was used by the US Navy from the latter part of World War II into the post-war era.
It was fitted in many different aircraft types for communication between aircraft, navigation, and communication back to base.
The set contains the AN/ARC-5 Receivers Units usually fitted inside the fuselage.
Full set with two different racks, two Receivers, three Trasnmitters and our special set of radio plugs.
Complementary Set: 24805 - 24807
KIT Content:
MT65 RACK + VHF + 2 RECEIVERS
This set provides all you need for the three-receivers configuration, airplane and wires not included.
You can find in the set a reproduction of MT-65 Rack Mount, one R-28 VHF Receiver, two R Receivers with plenty of plugs.
MT71 RACK +VHF+1 TRANSMITTER
This set provides all you need for the two-transmitters configuration, airplane and wires not included.
You can find in the set a reproduction of MT-71 Rack Mount, one t-23 VHF Transmitter, one T Transmitter(plugged) and plenty of plugs.
You might also like...
-
MX-SR UFN BLACK SURFACE CONDITIONER MULTIFLEX ULTRA FINE 3pcsSKU99001Scotch-Brite™ Multi-Flex Sheet is a thin, tough, highly conformable, sharp cutting and non-woven abrasive. The mutli-flex sheets are suitable for cleaning and finishing surfaces by hand.
Very flexible and conformable for cleaning or fine finishing replaces steel wool to eliminate contamination, they are very effective on 3D printed parts in plastic resin.
Can be used dry or wet and can be washed with clear water for long lasting duration.
UFN is the finest grade suitable for finishing and polishing.
Three 100x100mm pads in a pack.
-
MX-SR VFN PURPLE SURFACE CONDITIONER MULTIFLEX VERY FINE 3pcsSKU99002Scotch-Brite™ Multi-Flex Sheet is a thin, tough, highly conformable, sharp cutting and non-woven abrasive. The mutli-flex sheets are suitable for cleaning and finishing surfaces by hand.
Very flexible and conformable for cleaning or fine finishing replaces steel wool to eliminate contamination, they are very effective on 3D printed parts in plastic resin.
Can be used dry or wet and can be washed with clear water for long lasting duration.
VFN is a more coarse grade than UFN, suitable for finishing and polishing.
Three 100x100mm pads in a pack.
-
CR2 CA REMOVER 20grSKU99003Loxeal CA Remover CR2 is a solvent-free non-flammable blend to be used to remove cured cyanoacrylate adhesive from surfaces, clothing or to debond parts assembled with cyanoacrylate adhesives.
Long lasting removing action due to effective dissolving over time.
Designed to improve operating conditions of operators, with particular care for their health and safety, CA Remover CR2 doesn’t report on label any risk phrase or symbol because it is not classified as dangerous, according to actual directive on dangerous products.Use and application:
CA remover CR2, applied to cured cyanoacrylate adhesive, provides dissolving within several seconds or several minutes depending on the amount of adhesive.
Thin layers of adhesive can be wiped off with a cloth soaked in CA Remover.
Thick beads or drops will take between 30 to 60 seconds to dissolve the adhesive. A re-applying of product could be necessary.
Bonded parts may require several minutes of soaking. -
31-42 EPOXY GLUE 25mlSKU99004Multipurpose transparent structural adhesive, fast setting time.
Recommended for structural bonding of many materials: metals, ferrite, ceramic, marble, glass, concrete, wood and some plastics as polyester, ABS, rigid PVC.Not suitable for rubber, soft materials, polyethylene, polypropylene and PTFE. Bondings are well resistant to water, gasoline and oils.
curing time: 3 - 8 minutes