HSS-1 / H-34 CABIN DETAILS
Cargo or troop cabin details with internal frames and windows structure. All parts are ready to assembly as showed in the pictures. Also provided spare parts, cabin internal details to customize your model according to yoyr references.
Even if precise measurements have been taken same sanding and trimming may be necessary for perfect fit of parts.
This set is also avaliable in scale 1/48th
KIT Content:
RH part 1
Port side panel with internal and window structure with one window frame, emergency release handle and other realistic details.
Ready to assembly part
RH part 2
Port side main door frame for a realistic 3D reproduction of this very visibe part.
Ready to assembly.
RH part 3
Port side final part toward cockpit with realistic details.
Ready to assembly part as shown.
LH part 1
Startboard side panel with internal frames, window structure, emergency release handle and other realistic details.
Ready to assembly part as shown with two windows and frames
LH part 2
Startboard side panel with internal frames and other realistic details.
Ready to assembly part as shown.
LH part 3
Starboard port side final part toward cockpit with realistic details.
Ready to assembly part.
part 1
Recessed fuel filler cap as found on port fuselage. Just cut a square hole in the right position, trim and glue. Fast, easy and effective, a real Adriatic style part.
part 2
Recessed step as found on both sides of fuselage. Just cut a square hole in the right position, trim and glue. Fast, easy and effective, a real Adriatic style part.
You might also like...
-
MX-SR UFN BLACK SURFACE CONDITIONER MULTIFLEX ULTRA FINE 3pcsSKU99001Scotch-Brite™ Multi-Flex Sheet is a thin, tough, highly conformable, sharp cutting and non-woven abrasive. The mutli-flex sheets are suitable for cleaning and finishing surfaces by hand.
Very flexible and conformable for cleaning or fine finishing replaces steel wool to eliminate contamination, they are very effective on 3D printed parts in plastic resin.
Can be used dry or wet and can be washed with clear water for long lasting duration.
UFN is the finest grade suitable for finishing and polishing.
Three 100x100mm pads in a pack.
-
MX-SR VFN PURPLE SURFACE CONDITIONER MULTIFLEX VERY FINE 3pcsSKU99002Scotch-Brite™ Multi-Flex Sheet is a thin, tough, highly conformable, sharp cutting and non-woven abrasive. The mutli-flex sheets are suitable for cleaning and finishing surfaces by hand.
Very flexible and conformable for cleaning or fine finishing replaces steel wool to eliminate contamination, they are very effective on 3D printed parts in plastic resin.
Can be used dry or wet and can be washed with clear water for long lasting duration.
VFN is a more coarse grade than UFN, suitable for finishing and polishing.
Three 100x100mm pads in a pack.
-
CR2 CA REMOVER 20grSKU99003Loxeal CA Remover CR2 is a solvent-free non-flammable blend to be used to remove cured cyanoacrylate adhesive from surfaces, clothing or to debond parts assembled with cyanoacrylate adhesives.
Long lasting removing action due to effective dissolving over time.
Designed to improve operating conditions of operators, with particular care for their health and safety, CA Remover CR2 doesn’t report on label any risk phrase or symbol because it is not classified as dangerous, according to actual directive on dangerous products.Use and application:
CA remover CR2, applied to cured cyanoacrylate adhesive, provides dissolving within several seconds or several minutes depending on the amount of adhesive.
Thin layers of adhesive can be wiped off with a cloth soaked in CA Remover.
Thick beads or drops will take between 30 to 60 seconds to dissolve the adhesive. A re-applying of product could be necessary.
Bonded parts may require several minutes of soaking. -
31-42 EPOXY GLUE 25mlSKU99004Multipurpose transparent structural adhesive, fast setting time.
Recommended for structural bonding of many materials: metals, ferrite, ceramic, marble, glass, concrete, wood and some plastics as polyester, ABS, rigid PVC.Not suitable for rubber, soft materials, polyethylene, polypropylene and PTFE. Bondings are well resistant to water, gasoline and oils.
curing time: 3 - 8 minutes