F6F HELLCAT RADIO SET EARLY
The set provides parts for radios and IFF controls inside the cockpit, usuaslly found on F6F-3 or early F6F-5.
This set contains BC-450 and BC-451 control units of SCR-247 Radio Set, C-56 and C-57 control units of APX IIF Transponder and IFF selectors.
Full set with six units, two selectors and our special set of radio plugs.
This set is also avaliable in scale 1/24th
KIT Content:
BC-450 RECEIVER CONTROL UNIT
Three-Receiver Remote Control Box
This unit was used to remote control the BC-453 (A or B), the BC-454 (A or B) and the BC-455 (A or B)
Receivers in the three-receiver configuration.
BC-451 TRASMITTER CONTROL UNIT
Four-Transmitter Remote Control Box
This unit was used to remote control the BC-696-A, BC-457-A, BC-458-A, BC-459-A Transmitters.
C-57 EMERGENCY DESTRUCTOR IFF APX2
This unit was used ro remote control the aircraft Transponsder of AN/APXII IFF
C-56 TRANSPONDER CONTROL UNIT IFF APX2
This unit was used ro remote control the aircraft Transponsder of AN/APXII IFF
BC-958 CONTROL BOX
This unit was used to remote control the BC-966 Transponder SCR-595 and togheter BC-965 is part of RC-255-A Control Unit
BC-965 SELECTOR CONTROL BOX
This unit was used to remote control the BC-966 Transponder and togheter BC-958 is part of RC-255-A Control Uni
This unit tembodies the on-off switch and emergency switches.
IFF SELECTOR
IFF DESTRUCTOR
Related Products
-
F6F HELLCAT STATION 52 1/2 EARLYSKU24001This set contains tation 52 1/2 early as found on F6F-3 with seat supports, pilot armour early style 3/8 thick, three separated head rest to be used as for your references.
It is modelled without hydraulic plumbing lines so difficult to remove to enhance this important part of the cockpit.
It perfectly fits with other kit parts.
You might also like...
-
MX-SR UFN BLACK SURFACE CONDITIONER MULTIFLEX ULTRA FINE 3pcsSKU99001Scotch-Brite™ Multi-Flex Sheet is a thin, tough, highly conformable, sharp cutting and non-woven abrasive. The mutli-flex sheets are suitable for cleaning and finishing surfaces by hand.
Very flexible and conformable for cleaning or fine finishing replaces steel wool to eliminate contamination, they are very effective on 3D printed parts in plastic resin.
Can be used dry or wet and can be washed with clear water for long lasting duration.
UFN is the finest grade suitable for finishing and polishing.
Three 100x100mm pads in a pack.
-
MX-SR VFN PURPLE SURFACE CONDITIONER MULTIFLEX VERY FINE 3pcsSKU99002Scotch-Brite™ Multi-Flex Sheet is a thin, tough, highly conformable, sharp cutting and non-woven abrasive. The mutli-flex sheets are suitable for cleaning and finishing surfaces by hand.
Very flexible and conformable for cleaning or fine finishing replaces steel wool to eliminate contamination, they are very effective on 3D printed parts in plastic resin.
Can be used dry or wet and can be washed with clear water for long lasting duration.
VFN is a more coarse grade than UFN, suitable for finishing and polishing.
Three 100x100mm pads in a pack.
-
31-42 EPOXY GLUE 25mlSKU99004Multipurpose transparent structural adhesive, fast setting time.
Recommended for structural bonding of many materials: metals, ferrite, ceramic, marble, glass, concrete, wood and some plastics as polyester, ABS, rigid PVC.Not suitable for rubber, soft materials, polyethylene, polypropylene and PTFE. Bondings are well resistant to water, gasoline and oils.
curing time: 3 - 8 minutes
-
CR2 CA REMOVER 20grSKU99003Loxeal CA Remover CR2 is a solvent-free non-flammable blend to be used to remove cured cyanoacrylate adhesive from surfaces, clothing or to debond parts assembled with cyanoacrylate adhesives.
Long lasting removing action due to effective dissolving over time.
Designed to improve operating conditions of operators, with particular care for their health and safety, CA Remover CR2 doesn’t report on label any risk phrase or symbol because it is not classified as dangerous, according to actual directive on dangerous products.Use and application:
CA remover CR2, applied to cured cyanoacrylate adhesive, provides dissolving within several seconds or several minutes depending on the amount of adhesive.
Thin layers of adhesive can be wiped off with a cloth soaked in CA Remover.
Thick beads or drops will take between 30 to 60 seconds to dissolve the adhesive. A re-applying of product could be necessary.
Bonded parts may require several minutes of soaking.