Out of stock
SKU
32017

F6F HELLCAT RADIO SET LATE

The set provides parts for radios and IFF controls inside the cockpit, usuaslly found on F6F-5.

This set contains: C-38, C-26, C-27, C-45 Control Units of AN/ARC-5 Radio Set, BC-958 Control Box and BC-965 Selector Control for IFF Tranponder.

Full set six units and our special free set of radio plugs.

This set is also avaliable in scale 1/24th.

€15.00

KIT Content:

C-38 RECEIVER CONTROL UNIT

C-38 RECEIVER CONTROL UNIT

Three-Receiver Remote Control Box

This unit was used to remote control the Receivers in the three-receivers configuration

Typical installation: C-38, C-45, C-26, C-27, C30, R-28 VHF, any receiversfrom R-23 to R-27

C-26 RECEIVER CONTROL UNIT

C-26 RECEIVER CONTROL UNIT

Single Tunable Receiver Control Box

This unit was used to remotely controll the LF receiverr for ferry service with the R-27/ARC-5 used with MF or HF communications receivers.

C-27 RECEIVER CONTROL UNIT

C-27 RECEIVER CONTROL UNIT

Single Lock-Tuned Receiver Control Box

This unit was used to remotely controll the receiverr R-28/ARC-5 and the pre-set ARC-5 MF or HF communications receivers.

BC- 965 SELECTOR CONTROL BOX

BC- 965 SELECTOR CONTROL BOX

This unit was used to remote control the BC-966 Transponder and togheter BC-958 is part of RC-255-A Control Uni

This unit tembodies the on-off switch and emergency switches.

BC-958 CONTROL BOX

BC-958 CONTROL BOX

This unit was used to remote control the BC-966 Transponder SCR-595 and togheter BC-965 is part of RC-255-A Control Unit

C-45 TRANSMITTER CONTROL UNIT

C-45 TRANSMITTER CONTROL UNIT

This unit was used to remote control the transmitters

You might also like...

  1. MX-SR VFN PURPLE SURFACE CONDITIONER MULTIFLEX VERY FINE 3pcs
    MX-SR VFN PURPLE SURFACE CONDITIONER MULTIFLEX VERY FINE 3pcs
    SKU
    99002

    Scotch-Brite™ Multi-Flex Sheet is a thin, tough, highly conformable, sharp cutting and non-woven abrasive. The mutli-flex sheets are suitable for cleaning and finishing surfaces by hand.

    Very flexible and conformable for cleaning or fine finishing replaces steel wool to eliminate contamination, they are very effective on 3D printed parts in plastic resin.

    Can be used dry or wet and can be washed with clear water for long lasting duration.

    VFN is a more coarse grade than UFN, suitable for finishing and polishing.

    Three 100x100mm pads in a pack.

  2. MX-SR UFN BLACK SURFACE CONDITIONER MULTIFLEX ULTRA FINE 3pcs
    MX-SR UFN BLACK SURFACE CONDITIONER MULTIFLEX ULTRA FINE 3pcs
    SKU
    99001

    Scotch-Brite™ Multi-Flex Sheet is a thin, tough, highly conformable, sharp cutting and non-woven abrasive. The mutli-flex sheets are suitable for cleaning and finishing surfaces by hand.

    Very flexible and conformable for cleaning or fine finishing replaces steel wool to eliminate contamination, they are very effective on 3D printed parts in plastic resin.

    Can be used dry or wet and can be washed with clear water for long lasting duration.

    UFN is the finest grade suitable for finishing and polishing.

    Three 100x100mm pads in a pack.

  3. CR2 CA REMOVER 20gr
    CR2 CA REMOVER 20gr
    SKU
    99003

    Loxeal CA Remover CR2 is a solvent-free non-flammable blend to be used to remove cured cyanoacrylate adhesive from surfaces, clothing or to debond parts assembled with cyanoacrylate adhesives.
    Long lasting removing action due to effective dissolving over time.
    Designed to improve operating conditions of operators, with particular care for their health and safety, CA Remover CR2 doesn’t report on label any risk phrase or symbol because it is not classified as dangerous, according to actual directive on dangerous products.

    Use and application:
    CA remover CR2, applied to cured cyanoacrylate adhesive, provides dissolving within several seconds or several minutes depending on the amount of adhesive.
    Thin layers of adhesive can be wiped off with a cloth soaked in CA Remover.
    Thick beads or drops will take between 30 to 60 seconds to dissolve the adhesive. A re-applying of product could be necessary.
    Bonded parts may require several minutes of soaking.

  4. 31-42 EPOXY GLUE 25ml
    31-42 EPOXY GLUE 25ml
    SKU
    99004

    Multipurpose transparent structural adhesive, fast setting time.
    Recommended for structural bonding of many materials: metals, ferrite, ceramic, marble, glass, concrete, wood and some plastics as polyester, ABS, rigid PVC.

    Not suitable for rubber, soft materials, polyethylene, polypropylene and PTFE. Bondings are well resistant to water, gasoline and oils.

    curing time: 3 - 8 minutes

Powered by Redarea