Out of stock
SKU
32008

HSS-1 / H-34 WRIGHT R-1820 CYCLONE ENGINE, HIGH EXAUST

This set provides the Wright R-1820 Cyclone radial engine for H-34 / HSS-1. It comes with front clucth blade fan, side shroud, the particular intake and triple high exausts.

This set is also avaliable in scale 1/48th

 

 

 

€20.00

KIT Content:

engine main assembly

engine main assembly

Wright R-1820 Cyclone radial engine main assembly, it is a one-piece part.

engine fan

engine fan

Engine fan and cover.

intake

intake

The distinctive engine air intake of H-34.

shroud

shroud

Engine shroud,  with the round engine support modelled inside.

exhaust 1

exhaust 1

Late triple exhaust, installed in the upper half of engine that perfectly fits with engine cylinders.

exhaust 2

exhaust 2

Late triple exhaust, installed in the lower half of engine that perfectly fits with engine cylinders.

exhaust 3

exhaust 3

Late exhaust, installed in the upper half of engine for a single cylinder.

exhaust end parts

exhaust end parts

Exhaust end parts, notice that larger is installed on upper exhaust (exhaust 1)

You might also like...

  1. MX-SR UFN BLACK SURFACE CONDITIONER MULTIFLEX ULTRA FINE 3pcs
    MX-SR UFN BLACK SURFACE CONDITIONER MULTIFLEX ULTRA FINE 3pcs
    SKU
    99001

    Scotch-Brite™ Multi-Flex Sheet is a thin, tough, highly conformable, sharp cutting and non-woven abrasive. The mutli-flex sheets are suitable for cleaning and finishing surfaces by hand.

    Very flexible and conformable for cleaning or fine finishing replaces steel wool to eliminate contamination, they are very effective on 3D printed parts in plastic resin.

    Can be used dry or wet and can be washed with clear water for long lasting duration.

    UFN is the finest grade suitable for finishing and polishing.

    Three 100x100mm pads in a pack.

  2. MX-SR VFN PURPLE SURFACE CONDITIONER MULTIFLEX VERY FINE 3pcs
    MX-SR VFN PURPLE SURFACE CONDITIONER MULTIFLEX VERY FINE 3pcs
    SKU
    99002

    Scotch-Brite™ Multi-Flex Sheet is a thin, tough, highly conformable, sharp cutting and non-woven abrasive. The mutli-flex sheets are suitable for cleaning and finishing surfaces by hand.

    Very flexible and conformable for cleaning or fine finishing replaces steel wool to eliminate contamination, they are very effective on 3D printed parts in plastic resin.

    Can be used dry or wet and can be washed with clear water for long lasting duration.

    VFN is a more coarse grade than UFN, suitable for finishing and polishing.

    Three 100x100mm pads in a pack.

  3. CR2 CA REMOVER 20gr
    CR2 CA REMOVER 20gr
    SKU
    99003

    Loxeal CA Remover CR2 is a solvent-free non-flammable blend to be used to remove cured cyanoacrylate adhesive from surfaces, clothing or to debond parts assembled with cyanoacrylate adhesives.
    Long lasting removing action due to effective dissolving over time.
    Designed to improve operating conditions of operators, with particular care for their health and safety, CA Remover CR2 doesn’t report on label any risk phrase or symbol because it is not classified as dangerous, according to actual directive on dangerous products.

    Use and application:
    CA remover CR2, applied to cured cyanoacrylate adhesive, provides dissolving within several seconds or several minutes depending on the amount of adhesive.
    Thin layers of adhesive can be wiped off with a cloth soaked in CA Remover.
    Thick beads or drops will take between 30 to 60 seconds to dissolve the adhesive. A re-applying of product could be necessary.
    Bonded parts may require several minutes of soaking.

  4. 31-42 EPOXY GLUE 25ml
    31-42 EPOXY GLUE 25ml
    SKU
    99004

    Multipurpose transparent structural adhesive, fast setting time.
    Recommended for structural bonding of many materials: metals, ferrite, ceramic, marble, glass, concrete, wood and some plastics as polyester, ABS, rigid PVC.

    Not suitable for rubber, soft materials, polyethylene, polypropylene and PTFE. Bondings are well resistant to water, gasoline and oils.

    curing time: 3 - 8 minutes

Powered by Redarea