In stock
SKU
32021

WESSEX FRONT DETAILS SET

This set contains upper front detail set, with full internal structures and side panel with electric and later electronic devices. Full detail and parts to enhance a very visible part of this helicopter.

To show this set some accurate and sharp cuttings of model fuselages are necessary, so we recomend this set for advanced modellers only.

€18.00

KIT Content:

main assebly

main assebly

This part can be supplied as a single part, included in this set, or coupled with engine bay for a real museum-quality model

Please check our Wessex set NUMERO

box

box

electric engine control boxes, two parts supplied.

transmission

transmission

main transmission box. It isl usually full with tubing and wirig, a real eye-catcher

panel 1

panel 1

panel 2

panel 2

panel 3

panel 3

panel 4

panel 4

panel 5

panel 5

side panel with boxes ang gymos

You might also like...

  1. MX-SR UFN BLACK SURFACE CONDITIONER MULTIFLEX ULTRA FINE 3pcs
    MX-SR UFN BLACK SURFACE CONDITIONER MULTIFLEX ULTRA FINE 3pcs
    SKU
    99001

    Scotch-Brite™ Multi-Flex Sheet is a thin, tough, highly conformable, sharp cutting and non-woven abrasive. The mutli-flex sheets are suitable for cleaning and finishing surfaces by hand.

    Very flexible and conformable for cleaning or fine finishing replaces steel wool to eliminate contamination, they are very effective on 3D printed parts in plastic resin.

    Can be used dry or wet and can be washed with clear water for long lasting duration.

    UFN is the finest grade suitable for finishing and polishing.

    Three 100x100mm pads in a pack.

  2. MX-SR VFN PURPLE SURFACE CONDITIONER MULTIFLEX VERY FINE 3pcs
    MX-SR VFN PURPLE SURFACE CONDITIONER MULTIFLEX VERY FINE 3pcs
    SKU
    99002

    Scotch-Brite™ Multi-Flex Sheet is a thin, tough, highly conformable, sharp cutting and non-woven abrasive. The mutli-flex sheets are suitable for cleaning and finishing surfaces by hand.

    Very flexible and conformable for cleaning or fine finishing replaces steel wool to eliminate contamination, they are very effective on 3D printed parts in plastic resin.

    Can be used dry or wet and can be washed with clear water for long lasting duration.

    VFN is a more coarse grade than UFN, suitable for finishing and polishing.

    Three 100x100mm pads in a pack.

  3. CR2 CA REMOVER 20gr
    CR2 CA REMOVER 20gr
    SKU
    99003

    Loxeal CA Remover CR2 is a solvent-free non-flammable blend to be used to remove cured cyanoacrylate adhesive from surfaces, clothing or to debond parts assembled with cyanoacrylate adhesives.
    Long lasting removing action due to effective dissolving over time.
    Designed to improve operating conditions of operators, with particular care for their health and safety, CA Remover CR2 doesn’t report on label any risk phrase or symbol because it is not classified as dangerous, according to actual directive on dangerous products.

    Use and application:
    CA remover CR2, applied to cured cyanoacrylate adhesive, provides dissolving within several seconds or several minutes depending on the amount of adhesive.
    Thin layers of adhesive can be wiped off with a cloth soaked in CA Remover.
    Thick beads or drops will take between 30 to 60 seconds to dissolve the adhesive. A re-applying of product could be necessary.
    Bonded parts may require several minutes of soaking.

  4. 31-42 EPOXY GLUE 25ml
    31-42 EPOXY GLUE 25ml
    SKU
    99004

    Multipurpose transparent structural adhesive, fast setting time.
    Recommended for structural bonding of many materials: metals, ferrite, ceramic, marble, glass, concrete, wood and some plastics as polyester, ABS, rigid PVC.

    Not suitable for rubber, soft materials, polyethylene, polypropylene and PTFE. Bondings are well resistant to water, gasoline and oils.

    curing time: 3 - 8 minutes

Powered by Redarea