SCR 247 RADIO SET CONTROLLERS
SCR-247 is the Radio Set developed for USAAC planes adopted in 1941.
They were very similar to ARA-ATA and AN/ARC-5 even if there were some slight differences, the most evident one is that SCR-247 Receivers and Trasmitters were often left unpainted in NM.
This set contains the SCR-247 Controll Units usually fitted inside the cockpit.
Full set with four different controllers and our special set of radio plugs.
Complementary sets: 24802 - 24803 - 24804
KIT Content:
BC-450 RECEIVER CONTROL UNIT
Three-Receiver Remote Control Box
This unit was used to remote control the BC-453 (A or B), the BC-454 (A or B) and the BC-455 (A or B) Receivers in the three-receiver configuration.
BC-451 TRANSMITTER CONTROL UNIT
Four-Transmitter Remote Control Box
This unit was used to remote control the BC-696-A, BC-457-A, BC-458-A, BC-459-A Transmitters.
BC-473 RECEIVER CONTROL UNIT
Single Tunable Receiver Control Box
This unit was used to remote control the BC-453 (A or B), the BC-454 (A or B) and the BC-455 (A or B) receivers in the one-receiver configuratiion.
BC-496 RECEIVER CONTROL UNIT
Transmitter Control Box
This unit was used to remote control the BC-453 (A or B), the BC-454 (A or B) and the BC-455 (A or B) receivers in the two-receivers configuratiion
You might also like...
-
MX-SR UFN BLACK SURFACE CONDITIONER MULTIFLEX ULTRA FINE 3pcsSKU99001Scotch-Brite™ Multi-Flex Sheet is a thin, tough, highly conformable, sharp cutting and non-woven abrasive. The mutli-flex sheets are suitable for cleaning and finishing surfaces by hand.
Very flexible and conformable for cleaning or fine finishing replaces steel wool to eliminate contamination, they are very effective on 3D printed parts in plastic resin.
Can be used dry or wet and can be washed with clear water for long lasting duration.
UFN is the finest grade suitable for finishing and polishing.
Three 100x100mm pads in a pack.
-
MX-SR VFN PURPLE SURFACE CONDITIONER MULTIFLEX VERY FINE 3pcsSKU99002Scotch-Brite™ Multi-Flex Sheet is a thin, tough, highly conformable, sharp cutting and non-woven abrasive. The mutli-flex sheets are suitable for cleaning and finishing surfaces by hand.
Very flexible and conformable for cleaning or fine finishing replaces steel wool to eliminate contamination, they are very effective on 3D printed parts in plastic resin.
Can be used dry or wet and can be washed with clear water for long lasting duration.
VFN is a more coarse grade than UFN, suitable for finishing and polishing.
Three 100x100mm pads in a pack.
-
CR2 CA REMOVER 20grSKU99003Loxeal CA Remover CR2 is a solvent-free non-flammable blend to be used to remove cured cyanoacrylate adhesive from surfaces, clothing or to debond parts assembled with cyanoacrylate adhesives.
Long lasting removing action due to effective dissolving over time.
Designed to improve operating conditions of operators, with particular care for their health and safety, CA Remover CR2 doesn’t report on label any risk phrase or symbol because it is not classified as dangerous, according to actual directive on dangerous products.Use and application:
CA remover CR2, applied to cured cyanoacrylate adhesive, provides dissolving within several seconds or several minutes depending on the amount of adhesive.
Thin layers of adhesive can be wiped off with a cloth soaked in CA Remover.
Thick beads or drops will take between 30 to 60 seconds to dissolve the adhesive. A re-applying of product could be necessary.
Bonded parts may require several minutes of soaking. -
31-42 EPOXY GLUE 25mlSKU99004Multipurpose transparent structural adhesive, fast setting time.
Recommended for structural bonding of many materials: metals, ferrite, ceramic, marble, glass, concrete, wood and some plastics as polyester, ABS, rigid PVC.Not suitable for rubber, soft materials, polyethylene, polypropylene and PTFE. Bondings are well resistant to water, gasoline and oils.
curing time: 3 - 8 minutes